Electro/Hydraulic brake actuator provides 1000 psi of pressure for 1-3 axles equipped with drum brakes. Sealed housing provides a weather tight seal. Large reservoir capacity reduces the number of fill-ups required which reduces the bleed time as well as the risk of running the reservoir dry during brake bleeding. Aluminum enclosure provides anti-corrosive protection and prevents the elements from affecting reliability while the finned housing design dissipates heat efficiently. Proportional pressure output to the brakes corresponds to voltage output of the brake controller for smooth, reliable braking.
Details/Specs:
Provides 1000 PSI of pressure
For single, tandem, and triple axle trailers with drum brakes
Dimensions: 10.5" L x 5.5" W x 7" H
12V DC operation requires 4-wire hookup & at least 9 amp break-away kit
Uses DOT 3 or 4 brake fluid, holds 40 cubic inches (0.7 qts)
Meets or exceeds all DOT regulations and federal braking requirements
Manufacturer: DexterPart No: K71-650-00
Electro/Hydraulic brake actuator provides 1600 psi of pressure for 1-3 axles equipped with disc brakes. Sealed housing provides a weather tight seal. Large reservoir capacity reduces the number of fill-ups required which reduces the bleed time as well as the risk of running the reservoir dry during brake bleeding. Aluminum enclosure provides anti-corrosive protection and prevents the elements from affecting reliability while the finned housing design dissipates heat efficiently. Proportional pressure output to the brakes corresponds to voltage output of the brake controller for smooth, reliable braking.
Details/Specs:
Provides 1600 PSI of pressure
For single, tandem, and triple axle trailers with disc brakes
Dimensions: 10.5" L x 5.5" W x 7" H
Distance between mounting holes (center to center):
2-1/2" Between holes on same side of bracket
9-13/16" Between holes on opposite sides of bracket
Mounting hole diameter: 1/4"
Hydraulic port size: 3/16"
12V DC operation requires 4-wire hookup & at least 9 amp break-away kit
Uses DOT 3 or 4 brake fluid, holds 40 cubic inches (0.7 qts)
Meets or exceeds all DOT regulations and federal braking requirements
Manufacturer: DexterPart No: K71-651-00
Electric-hydraulic brake actuator lets you use an electric brake controller from inside your vehicle to adjust and control your trailer's hydraulic brakes. Gives you greater control over your trailer's brakes than that provided by standard hydraulic actuators. Sealed, extruded, anodized aluminum housing (not cast or plastic) to prevent corrosion.
Details/Specs:
Dimensions: 12" L x 3" W x 7 1/4" H
Trailer mounted 12 V DC operation
Requires in-cab controller
Provides 1000 PSI for any trailer configuration with drum brakes and 1-3 axles
Uses DOT 3 or DOT 4 brake fluid
Meets all DOT regulations & complies with CFR-393 braking requirements
2 year warranty from date of purchase
Manufacturer: HydrastarPart No: 21-350
Electric-hydraulic brake actuator lets you use an electric brake controller from inside your vehicle to adjust and control your trailer's hydraulic brakes. Gives you greater control over your trailer's brakes than that provided by standard hydraulic actuators. Sealed, extruded, anodized aluminum housing (not cast or plastic) to prevent corrosion.
Details/Specs:
Dimensions 11.8inch long x 3inch wide x 7.3inch high
Trailer mounted 12 V DC operation
Requires in-cab controller
Provides 1600 PSI for any trailer configuration with disk brakes and 1-3 axles
Uses DOT 3 or DOT 4 brake fluid
Meets all DOT regulations & complies with CFR-393 braking requirements
2 year warranty from date of purchase
Manufacturer: Hydrastar
Manufacturer Part Number: HBA-16
Our Part No: 21-352-1