Jacks

The RV Camper Leveler is the fastest and easiest way to level your trailer camper. This kit is easy to use and levels your trailer in minutes. Simply place the leveler under the low-side tire and drive up until you reach level. Then, place the attached chock under the leveler to secure it in place and you're done. Each kit includes one leveler and one chock for a single wheel. For two axle trailers, you will need two kits. Details/Specs: Level from 1/2" to 4" For use with trailers up to 30,000 Lbs and up to 32" tire diameter  Made is USA with recycled materials 3-year limited warranty

Read more less

16" jack crank handle extension for 10K/12K gooseneck trailer jacks. 1" x 3 1/2" extension sleeve, grease fitting, and hardware included.

Read more less

Top-wind swivel pipe mount jack. This is the jack commonly used as support jacks on the back of PJ Trailers Car Hauler and Buggy hauler Trailers, and also as the tongue jack on most PJ Trailers U6, U7, U8, C4, and C5 models. Details/Specs: 5,000 lbs. lift/static capacity This is the same jack that is commonly used as support jacks on the back of the PJ Trailers Car Hauler and Buggy Hauler trailers. This is the standard tongue jack that is put on most PJ Trailers U6, U7, U8, C4, and C5 model trailers. Overall Length Retracted : 20" Travel : 15" Pipe ID : 2" Retracted to Center of swivel :12-3/4" Extended to Center of swival : 27.75"

Read more less

Replacement jack crank handle. 6" of clearance.

Read more less

The Andersen 'Trailer Jack Block' eliminates nearly all of the movement in your parked RV or Trailer! Each block comes with built-in magnets so you can attach each block to the bottom of your stabilizer and hit auto-level - no need to check and adjust each block. Fast and super-convenient!  For best results, use two blocks at the front and two in the back of your RV or Trailer. For trailers with more than 4 stabilizer jacks, use one block per stabilizer. Details/Specs: 8" high (14" double stacked) 12" diameter base & 10" diameter top Recessed pad area is 9-1/8" diameter, recessed post-hole is 2-1/2" diameter Each block weighs 5.3 lbs Rated 6,000 lbs (single block) and 1,500 lbs (double-stack) Eliminates nearly all movement and sway in parked RV's and Trailers Less stress on your RV or Trailer Extremely strong and durable Stackable for extra height (max 2 high)  Powerful, built-in magnets for easy set up Resists dirt, grime and oil 100% Made in the USA Lifetime Warranty

Read more less

Replacement jack crank handle for Jost jacks. This handle is similar to a standard gooseneck jack crank handle but is longer to clear the side of the trailer. 19" of clearance.

Read more less

sonstructed of heavy-duty, corrosion-resistant cast aluminum for commercial or consumer use. Serves as a jack for easy tire changes on tandem-axles and a wheel chock to help keep your trailer in place on inclines and most surfaces. Enables you to easily change a tire on your tandem-axle trailer and can also be used as a leveler for an RV when parked on uneven terrain. Details/Specs: 20,000 lbs capacity. Lifetime warranty. Made in USA Manufacturer: BlaylockManufacturer's Part Number: EZ100

Read more less

This square topwind jack has a large rectangular base foot and features a painted outer tube with plated inner tube and drop leg. Details/Specs: Direct weld to outer square tube 7,000 lbs. lift 8,000 lbs. support 15″ Travel 13.50″ additional drop leg extension

Read more less

 Constructed with 4" square tubing and 7-gauge superior alloy steel. State of the art 2-speed gearbox with power and speed for the most effective and efficient jack at all loads. Designed for today's standard agricultural, construction and industrial trailer applications. User friendly design makes operation smooth and easy. Engineered alloys for enhanced strength, stability and side load capability. Planetary gearbox fits within the width profile of the jack's outer tube eliminating the need for spacers. Easy-lifting 27 turns per 1" (planetary) and 29 turns per 1" (traditional) of travel. In high gear, the cranking ratio is a speedy 9 turns per 1" of travel, the fastest in its weight class. Details/Specs: Lift Capacity: 10,000 lbs Static Capacity: 12,000 lbs Dropleg Travel: 12-1/2" Dropleg pull-pin to the front. Adjustable dropleg with spring return and additional adjustment of 13-1/2" Weld on application with black finish Crank handle not included Manufacturer: BulldogManufacturer's Part Number: 183816

Read more less

Constructed with 4" square tubing and 7-gauge superior alloy steel. Used as the "slave" jack with a 2-speed jack set. Easy-access gear box with grease fitting for routine maintenance. Weld on application with black powder coat finish. Details/Specs: Lift Capacity: 10,000 lbs Static Capacity: 12,000 lbs Dropleg Travel: 12 1/2" 1:1.5 gear ratio Dropleg pull-pin to the front Adjustable dropleg with spring return and additional adjustment of 13-1/2" Crank handle not included Manufacturer: BulldogManufacturer's Part Number: 182815

Read more less

This is a sidewind jack with drop leg for gooseneck trailers. Weld on application with black powder coat finish. Details/Specs: Lift Capacity: 10,000 lbs. Static Capacity: 12,000 lbs. Drop leg Travel: 12-1/2" Drop leg pull-pin to the front Adjustable drop leg with spring return and additional adjustment of 13-1/2" Crank handle not included

Read more less

This sidewind industrial drop-leg jack features 15" of travel and 13-1/2" of additional adjustment. Constructed from heavy-guage 2-1/2" square tubing for direct weld mounting. Bushing are oil-impregnated for improved bearing and gear life. Details/Specs: 5,000 lbs lift 8,000 lbs of support Includes crank handle, heavy-duty base, grey outer tube and zinc-plated inner tube. Manufacturer: BulldogManufacturer's Part Number: 190754

Read more less

Bulldog's 5,000 lb. support capacity square jack dramatically improves side load strength while maintaining the economical benefits of lower capacity jacks. The extra side load strength while maintaining the economical benefits of lower capacity jacks. The extra side load capacity you need without the costs of increasing overall capacity. Details/Specs: Bracket height: 15-1/8" Retracted 30-1/8" Extended Lift: 15" Clearance: 9-1/4" from mounting bracket to top of jack Tubing width: 2-1/4" Pipe mount dimensions: 2" x 2" Handle radius: 6-1/2" Lift capacity: 3,000 lbs Static capacity: 5,000 lbs Weather-resistant coating on outer tube and zinc inner tube Manufacturer: BulldogPart No: 195362

Read more less

Jack motor compatible with all Bulldog single speed and traditional style gear box, 2 speed units used in tandem with a single speed slave jack. Permanently lubricated to provide years of maintenance free use. Custom designed wiring harness & rocker switch enclosed in a weather proof box. Kit includes all necessary components for ease of installation Details/Specs: 7,500 lbs capacity State of the art 12VDC electric motor 5 year warranty Manufacturer: BulldogManufacturer's Part Number: 182420

Read more less

Bulldog Jack Topwind 7K 4 & 5" Channel Utility will work with both 4 & 5" with 4 hole.  These come unpainted

Read more less

BULLDOG round jacks are recognized as the industry standard by leading agricultrual, commercial, horse, livestock, and other trailer manufacturers. For more than three quarters of a centruy, BULLDOG jacks have been demonstrated to be the most reliable, field-proven jacks on the market. Smooth, comfortable, ergonomic design Dependable vertical and side load capacity Proven reliability for long term use at rated loads Precision fitted parts for extra stability A-Frame models listed have grey painted outer and inner tubes - All other models have grey painted outer and clear zinc inner tubes Part# 18-460

Read more less

Replacement jack handle for 7K topwind jacks.

Read more less

This is a sidewind jack with drop leg for gooseneck trailers. Weld on application with black powder coat finish. Details/Specs: Lift Capacity: 10,000 lbs. Static Capacity: 12,000 lbs. Drop leg Travel: 12 1/2" Drop leg pull-pin to the side Adjustable drop leg with spring return and additional adjustment of 13-1/2" Crank handle not included

Read more less

6" Plastic caster wheel, 1,200 lbs capacity

Read more less

Jack, 7K Dropleg Square Topwind- Unpainted

Read more less